How to Fix a Broken Bed Frame: The Definitive Guide

Your bed frame could split because of wear and tear. It is natural, and you may not be able to do much about it. In case you want to replace the expensive bed, a new bed frame would cost a lot of money. The good news is that you can avoid these costs and repair the bed frame yourself. Do you want to know how to fix a broken wooden bed frame? But before that, you need to be aware of what caused the damage. At times your bed frame may need some wood filler to fill up the cracks. At other times you may have to go for more extensive repairs to replace any element that is broken.

We all desire a comfortable sleep, and the bed’s quality plays a significant role in this. Bed frames hold the mattress in place; however, if the bed frame does not have proper support, this will cause the mattress to move from its place and disrupt your sleep. A weak bed frame will make the mattress sag, and this is when you will think about replacing the bed frame.

Bed frame cracks can be due to many factors. The type of wood used, the material and its strength, and the pressure on the bed frame are some factors that can destroy the frame. The cracks appear gradually, which eventually causes the bed to break.

Each problem has a different solution. Here are some of the common issues discussed, along with the cause and the best solution to fix a wooden broken bed frame.

How to fix cracks and splits in a bed frame?

Splits and cracks are common, and these tend to develop when the bed frame does not have enough support. The split may be on the horizontal grainline or either side of the bed frame. The crack can also be at the end of the frame, but it is important to remember that these cracks develop in the bed’s foundation, which can be alarming. To repair this, you have to put in a few new beams to strengthen the existing structure.

For small cracks:

  • If you notice small cracks on your bed, all you need is some putty to mend it. 
  • Use sandpaper and make the sides around the crack as smooth as you can. It will let the wood filler to get appropriately bound.
  • It will help if you place some wood filler until the crack gets filled. 
  • The excess filler can be taken out using a putty knife. 
  • Then leave the cracks to dry. 
  • If you do not wish to let the cracks be visible, then you may paint on the area.

For large cracks:

  • If you notice that the cracks are bigger, then wood filers would not help.
  • Make use of sandpaper to smooth the sides around the crack. 
  • Use a damp cloth to wipe the area, which will make the glue to bind them well.
  • Use a clamp to measure the two sides, and for that, you will have to hold the area tightly. 
  • Apply wood glue to the area once you notice that the clamp is ready. Make sure that you use the glue liberally. Also, to avoid any mess, keep an old blanket handy so that the glue does not drip onto your furniture. 
  • You need to clamp down on the area and use the putty knife to scrape out any excess glue. Leave the glue to let it dry, and use sandpaper to remove the excess glue to create a smooth surface. 
  • The crack is fixed. 
  • For a long-lasting result, you should add some extra support to your bed frame. 

How to fix bad joints in a bed frame?

Bad joints are common, especially if you have antique beds that are made of tenon and mortise. These joints loosen, and you need to know how to fix a broken bed support to mend your broken bed. These joints may have been reinforced using metal brackets, or it is possible that there were brackets attached when the frame was new. 

  1. To repair the bad bed joints, you will have to take off the bracket, repair the joint, and then replace the bracket.
  2. To remove the bracket, you should use the drill or a driver and then unscrew the screws that hold the frame and the metal bracket. These metal brackets are normally folded and placed at 90 degrees on each corner’s inner side. In case you notice that your bed has brackets, these can be seen screwed on the tenon and mortise joints.
  3. The next step is to disassemble and clean it. For this check, the joints and if you find that they are loose, then use a rubber mallet and then tap it apart. Any dried glue should be scraped out using a chisel. However, if these are fixed firmly, then do not pull them apart. Measure the tenon and then cut two pieces of wooden tape. 
  4. Now glue this wood tape on the tenon, which will give it extra width. Liberally apply glue to the slot that holds the tenon. Now reassemble the frame with a rubber mallet to bind it together.
  5. The last step is to replace the bed brackets making sure that the holes created for the old screw do not match with the existing holes in your bracket. Screw the brackets with the original screw.

How to fix a broken bed slat?

Do you know that the bed slat could be broken at times and it is also relatively simple to replace.

Now, let’s discuss how to fix a broken bed slat. It can be due to the mattress’s constant pressure and accelerated in case the mattress is not spread evenly. All that you need to do is to fix the bed slat. 

  • Remove the broken slat and throw it off away. 
  • Measure the unbroken slat. It would be best if you take an accurate measurement of the length, width, and thickness, and once you have these details
  • Get a replacement for it. 
  • It would be best if you are extra careful with the width and thickness. 
  • Line the slat with the other slats and then place it into its exact position. 
  • You may want to add some glue to offer extra security, or you may also want to screw it.

In Conclusion 

Bed frames are expensive, and you should consider bed frame repair first before you plan to discard and buy a new one. Some common bed problems can be easily fixed at home, without the help of a carpenter. Attrition affects every bed, be it an antique or a contemporary bed. The bed frames have to bear the brunt of excess weight, not to forget the toddlers jumping around it all the time, and if the bed frames cannot handle it, they can cause the bed frame to break.

The good news is that these issues can be fixed with simple materials. However, if you cannot detect the problem’s exact cause and find that your bed sags, then the problem may also be with the box spring. To avoid this trouble of repairing your broken bed each time, it always pays to go for a bed made of good quality wood. 

You May Also Like…

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *